TRAINING.

Grounding and Bonding of Electrical Systems

Ottawa, Ontario /
May 14 - 15, 2019 /
Course Code: 10-0512-2365

REGISTER NOW
The confirmation of a course and venue depends on early registration; Register early to avoid the postponement or cancellation of a course.
  • Overview
  • Syllabus
  • Instructor
  • Location

Overview

After participating in this course, you will be able to:

  • Identify and prevent safety hazards to personnel who come in contact with electrical systems
  • Prevent equipment failures and malfunctions by employing proper grounding techniques
  • Interpret codes and standards related to grounding
  • Ensure proper operation of communication, computer and control systems by proper grounding and bonding
  • Apply to your projects lightning protection methods

Description:
Grounding and bonding systems ensure that electrical systems are safe from electric shock and fires by limiting the voltage imposed by lightning, line surges, or unintentional contact with high voltage lines as well as a ground-fault. An integrated approach of theory and practice will ensure you have a firm foundation of knowledge when you begin your next design or construction project, or when you encounter problems in your electrical system which must be corrected for safety, operational or power quality reasons.

Case studies will be presented to discuss grounding and bonding applications in a variety of areas (industrial and substation) in order to reinforce fundamental grounding principles common to a variety of applications.

Course Outline:

  • Grounding
  • Grounding vs. bonding
  • Electrical code requirements and standards
  • Grounding resistance and resistivity
  • Substation grounding
  • Electronic equipment
  • Lightning protection
  • Measurement techniques

Who Should Attend:
Electrical Engineers • Design Engineers • Managers • Project Managers • Power Quality Specialists • Maintenance Managers • Consultants • Electronics and Controls personnel • Traffic Signal Designers and Operators • Technologists

More Information

Syllabus

Daily Schedule
8:00 Registration & Coffee (Day 1 only)
8:30 Seminar begins
12:00 Lunch (provided)
4:30 Adjournment

There is a one‐hour lunch break each day in addition to a refreshments and networking break each morning and afternoon. Lunch and refreshments are provided.

Day I

Welcome, Introduction, Workshop Preview, Learning Outcomes and the Assessment Method

Introduction

  • Definitions
  • Electrical code objectives
  • Ground currents
  • Resistance and resistivity
  • Electrical hazards- shock and blast

What Is Grounding?

  • Grounding methods
  • Electrical code requirements
  • System grounding – single and multiple services
  • Unwanted current flow
  • Grounding electrodes and grounding methods
  • Integrating  emergency generators

Electrical Safety Grounding

  • Common electrical hazards
  • Rules for working around live electrical equipment
  • Electrical safety grounding
  • Work place electrical safety and electrical code requirements

What Is Bonding?

  • Grounding and bonding – the differences
  • Body resistance and electric shock
  • Bonding definition and purposes
  • Electrical code requirements
  • Methods of bonding and what must be bonded

Other Important Information

  • Ground faults – impedance effects and effective fault paths
  • Earth resistivity
  • Ground fault protection
  • Single conductor cables – circulating sheath currents

Questions and Answers

Adjournment

Day II

Substation Grounding

  • Permissible body currents
  • Step and touch potentials
  • Grounding resistance and resistivity
  • Substation ground electrodes
  • ANSI/IEEE grounding standard

Electronic Equipment

  • Frequency and power quality
  • Frequency response of conductors
  • Minimizing electrical interference
  • Shielding methods

Lightning Protection

  • The nature of lightning
  • Lightning protection principles and methods
  • Protection equipment and grounding methods
  • Surge protection and insulation coordination

Measurement Techniques

  • Ground resistance and resistivity
  • Effects of moisture and temperature
  • Measurement methods

Case Study I – Retrofitting an Existing Installation

Case Study II – Surge Protection

Questions and Answers and Feedback to Participants on Achievement of Learning Outcomes

Final Adjournment

Instructor

Ajit Bapat, P.Eng., M.Eng., MBA

Ajit is well known in the electrical distribution field for his 40 years of expertise in the art and science of ground fault protection.

He holds Master's degrees in business administration and electrical engineering, specializing in power systems and power system protection. He has particular interest in ground fault protection; digital metering systems; microprocessor based integrated systems for protection; and the metering, monitoring, and control of power distribution systems. A member of Professional Engineers Ontario, he is also a senior life member of the IEEE.




Venue

Ottawa Conference & Event Centre
200 Coventry Road
Ottawa, ON K1K 4S3
613 288-3450
REGISTER NOW
NOT INTERESTED IN THIS COURSE?

We always want to improve the quality of our courses. Please select any reasons why you feel this course is inadequate (check all that apply).

Please check this box:
Course Rating
4.5 out of 5

Overall rating of this course by its previous attendees!

Fee & Credits
  • 1.4 Continuing Education Units (CEUs)
  • 14 Professional Development Hours (PDHs)
Early Registration Fee:

$1595 + taxes

Fee after April 5, 2019:

$1695 + taxes

Register




On-Site Training
This course can be customized and delivered to your group of staff at your facility, saving time and money.
REQUEST A QUOTE
OTHER LOCATIONS
Grounding and Bonding of Electrical Systems   Richmond, BC | Mar 19 - 20, 2019
Grounding and Bonding of Electrical Systems   Edmonton, AB | Oct 16 - 18, 2019
E-Newsletter
EPIC's email newsletter is a great source of information for:

  • course updates
  • surveys
  • informative articles/papers
  • exclusive discounts
Subscribe
Top