Electrical Controls and Safety
Nov 1, 2022 /
Course Code: 13-1121-ONL22
This course is held online over 1 day on the following schedule (All times in Eastern Time Zone):
10:00 am to 6:00 pm Eastern (Will include the usual breaks and lunch)
After participating in the course, you will be able:
- To look for, inspect, verify, and validate the electrical, controls, and integration design, for equipment and systems provided by Original Equipment Manufacturers (OEMs) and control system suppliers. Safety and glitches of electrical equipment usage will be well understood.
The training will start with a detailed overview of electrical power systems and its applications on machines and manufacturing of system components. Things to look for, inspect, verify, and validate the electrical, controls, and integration design, for equipment and systems provided by Original Equipment Manufacturers (OEMs) and control system suppliers. Grounding and bonding of electrical equipment and installation within electrical manufacturing and facilities will be covered. Safety and Control of machines will be described (arc flash, labeling, etc.)
- Basic Definitions
- Electrical Dangers and How to Avoid
- Electrical Control Panels, Enclosures, and Components
- Machine Wiring and Devices
- Labeling and Tagging
- Machine Level: Field Assembly
Who Should Attend
Electrical Engineers • Design Engineers • Managers • Project Managers • Power Quality Specialists • Maintenance Managers • Consultants • Electronics and Controls personnel • Mechanical Designers and Operators • TechnologistsMore Information
Time: 10:00 AM - 6:00 PM Eastern Time
Please note: You can check other time zones here.
- AC current and DC current
- Voltage and Amperage
- Ohm’s Law
- Single-phase, and three-phase, Two phase?
- Use examples – ex. What we use at home, when we say :110V, 208V what does that mean?
- Usual Voltage of circuits
- Transformers? What are they, how do they work?
- What happens with a fuse blows? How do we avoid in design?
- What happens during a power glitch? How do we design to minimize?
- What’s a circuit breaker?
- What is a bus bar?
- How does a typical panel look like? How does it draw power? Make sure it’s cooled; things to keep in mid
- GFCIs, AFCIs
- What’s the reset and test button on an electrical outlet on the wall?
Electrical Dangers & How to Avoid
- Shock hazard
- Arc Flash hazard
- Arc Blast
- Fire Ignition
- Grounding and bonding
Electrical Control Panels, Enclosures, and Components
This area of inspection is to ensure that the electrical design and fabrication of the control panels and controls components are of the highest workmanship, and that they are in compliance with the project’s design specifications.
- Panels in environmental conditions
- Panels size and capacity
- Panels cleanliness
- Main disconnect switch (LOTO)
- PLC network architecture
- Components labeling
Machine Wiring and Devices
This area of inspection is to ensure that the electrical design and fabrication of the wiring and devices on the machine are of the highest quality/workmanship, and that they are in compliance with the project’s design specifications.
- All machine wiring and installation of devices is complete
- All machine wiring is neat, organized, and adequately protected
- Enclosures and devices are properly grounded (earthed)
- All wireways, raceways, and conduits are of an approved type
- Machine wiring does not present a hazard to operators and maintenance
- All cordsets and cables are adequately fastened to the machine
- All devices are properly mounted
- Hygenic Design for Cable Routing
Labeling and Tagging
This area of inspection is to ensure that the labeling and tagging of components and equipment is complete and in compliance with the project’s design specifications.
- Devices and components are labeled according to the electrical schematics
- Shock warning labels are applied
- Main Electrical Panel has required nameplate
- All wiring and cables are labeled
- Arc flash labels
- ESA / CSA / ULC Labels
Machine Level: Field Assembly
This area of inspection is to ensure that the equipment shipped to the site is re-assembled and installed completely and properly.
- Main electrical power supply
- Main air supply
- Field-mounted instruments, sensors, and devices
- I/O checkout is complete
- Electrical wireways, raceways, and electrical enclosures are secure
Khaled is a registered professional engineer and general manager of TEEBA Engineering Inc. He has extensive experience in substation design, power system studies, power quality audits, EMF and grounding design, field testing and EHS program settings.
Khaled received his M.Sc. from The University of New Brunswick and his MBA from Laurier School of Business. He has managed and executed various electrical engineering projects for major electrical, industrial and commercial facilities in Canada and the US.
He has various IEEE publications, is a technical reviewer for many IEEE journals and is a certified electrical safety trainer for GE. Khaled has been the recipient of GE Management Award and has many leadership certifications from GE Leadership Development Centre at Crotonville.
As a certified electrical safety trainer by GE Corporate, Khaled has taught many technical courses across Canada, USA, Asia and Middle East to industrial customers, electrical consultants and electrical utilities customers.
NOT INTERESTED IN THIS COURSE?
We always want to improve the quality of our courses. Please select any reasons why you feel this course is inadequate (check all that apply).
Overall rating of this course by its previous attendees!
Fee & Credits
$695 + taxes
- 0.7 Continuing Education Units (CEUs)
- 7 Professional Development Hours (PDHs)
- ECAA Annual Professional Development Points
REQUEST A QUOTE
Canada Job Grant
Your company may be eligible for funding! LEARN MORE